Меню

Индустриален рутер Teltonika RUT204, 4G LTE Cat4, GNSS, RS232, PoE-In, RMS, Dual SIM, Wi-Fi 4, RutOS

Промо
  • Наличност: Със заявка от производител
  • Код на продукт: RUT2040AAAA0-TEL
  • Код на производител: RUT2040AAAA0
Производител: Teltonika


Ревюта: (0)
  • Описание
  • Спецификация
  • Отзиви (0)

Детайлна информация

Mobile

Mobile module4G LTE Cat 4 up to 150 DL/50 UL Mbps; 3G up to 21 DL/5.76 UL Mbps; 2G up to 236.8 DL/236.8 UL kbps

3GPP ReleaseRelease 9

SIM switch2 SIM cards, auto-switch cases: weak signal, data limit, SMS limit, roaming, no network, network denied, data connection fail, SIM idle protection

StatusIMSI, ICCID, operator, operator state, data connection state, network type, bandwidth, connected band, signal strength (RSSI), SINR, RSRP, RSRQ, EC/IO, RSCP, data sent/received, LAC, TAC, cell ID, ARFCN, UARFCN, EARFCN, MCC, and MNC

SMSSMS status, SMS configuration, EMAIL to SMS, SMS to EMAIL, SMS to HTTP, SMS to SMS, scheduled SMS, SMS autoreply, SMPP

USSDSupports sending and reading Unstructured Supplementary Service Data messages

Block/Allow listOperator block/allow list (by country or separate operators)

Band managementBand lock, Used band status display

SIM idle protection serviceProvides the possibility to configure the router to periodically switch to the unused SIM card and establish a data connection in order to prevent the SIM card from being blocked

SIM PIN code managementSIM PIN code management enables setting, changing, or disabling the SIM card's PIN

APNAuto APN

BridgeDirect connection (bridge) between mobile ISP and device on LAN

PassthroughRouter assigns its mobile WAN IP address to another device on LAN

Wireless

Wireless mode802.11b/g/n (Wi-Fi 4), Access Point (AP), Station (STA)

Wi-Fi securityWPA2-Enterprise: PEAP, WPA2-PSK, WPA-EAP, WPA-PSK, WPA3-SAE, WPA3-EAP, OWE; AES-CCMP, TKIP, Auto-cipher modes, client separation, EAP-TLS with PKCS#12 certificates, disable auto-reconnect, 802.11w Protected Management Frames (PMF)

SSID/ESSIDSSID stealth mode and access control based on MAC address

Wi-Fi usersUp to 50 simultaneous connections

Wireless Connectivity FeaturesFast roaming (802.11r), Relayd, BSS transition management (802.11v), radio resource measurement (802.11k)

Wireless MAC filterAllowlist, blocklist

Wireless QR code generatorOnce scanned, a user will automatically enter your network without needing to input login information

TravelMateForward Wi-Fi hotspot landing page to a subsequent connected device

Ethernet

WAN1 x WAN port 10/100 Mbps, compliance with IEEE 802.3, IEEE 802.3u, 802.3az standards, supports auto MDI/MDIX crossover

LAN1 x LAN port, 10/100 Mbps, compliance with IEEE 802.3, IEEE 802.3u, 802.3az standards, supports auto MDI/MDIX crossover

Network

RoutingStatic routing, Dynamic routing (BGP, OSPF v2, RIP v1/v2, EIGRP, NHRP), Policy based routing

Network protocolsTCP, UDP, IPv4, IPv6, ICMP, NTP, DNS, HTTP, HTTPS, SFTP, FTP, SMTP, SSL v3, TLS, ARP, VRRP, PPP, PPPoE, UPNP, SSH, DHCP, Telnet, SMPP, SNMP, MQTT, Wake on Lan (WOL), VXLAN

VoIP passthrough supportH.323 and SIP-alg protocol NAT helpers, allowing proper routing of VoIP packets

Connection monitoringPing Reboot, Wget Reboot, Periodic Reboot, LCP and ICMP for link inspection

FirewallPort forward, traffic rules, custom rules, TTL target customisation

Firewall status pageView all your Firewall statistics, rules, and rule counters

Port managementView device ports, enable and disable each of them, turn auto-configuration on or off, change their transmission speed, and so on

Network topologyVisual representation of your network, showing which devices are connected to which other devices

DHCPStatic and dynamic IP allocation, DHCP relay, DHCP server configuration, status, static leases: MAC with wildcards

QoS / Smart Queue Management (SQM)Traffic priority queuing by source/destination, service, protocol or port, WMM, 802.11e

DDNSSupported >77 service providers, others can be configured manually

DNS over HTTPSDNS over HTTPS proxy enables secure DNS resolution by routing DNS queries over HTTPS

Network backupWi-Fi WAN, Mobile, VRRP, Wired options, each of which can be used as an automatic Failover

Load balancingBalance Internet traffic over multiple WAN connections

HotspotCaptive portal (hotspot), internal/external Radius server, Radius MAC authentication, SMS authorisation, SSO authentication, internal/external landing page, walled garden, user scripts, URL parameters, user groups, individual user or group limitations, user management, 9 default customisable themes and optionality to upload and download customised hotspot themes

Hotspot 2.0Hotspot 2.0 is a Wi-Fi standard that enables seamless, secure, and automatic connection to trusted wireless networks

SSHFSPossibility to mount remote file system via SSH protocol

Traffic ManagementReal-time monitoring, wireless signal charts, traffic usage history

Security

AuthenticationPre-shared key, digital certificates, X.509 certificates, TACACS+, Internal & External RADIUS users authentication, IP & login attempts block, time-based login blocking, built-in random password generator

FirewallPreconfigured firewall rules can be enabled via WebUI, unlimited firewall configuration via CLI, DMZ, NAT, NAT-T, NAT64

Attack preventionDDOS prevention (SYN flood protection, SSH attack prevention, HTTP/HTTPS attack prevention), port scan prevention (SYN-FIN, SYN-RST, X-mas, NULL flags, FIN scan attacks)

VLANPort and tag-based VLAN separation

Mobile quota controlMobile data limit, customizable period, start time, warning limit, phone number

WEB filterBlock list for blocking out unwanted websites, allow list for specifying allowed sites only

Access controlFlexible access control of SSH, Web interface, CLI and Telnet

Certificate ManagerCertificate creation tool allows to create CA, server, client, let's encrypt, SCEP certificates

802.1xPort-based network access control server

VPN

OpenVPNMultiple clients and a server can run simultaneously, 27 encryption methods

OpenVPN EncryptionDES-CBC 64, RC2-CBC 128, DES-EDE-CBC 128, DES-EDE3-CBC 192, DESX-CBC 192,

BF-CBC 128, RC2-40-CBC 40, CAST5-CBC 128, RC2-64-CBC 64, AES-128-CBC 128, AES-128-CFB 128, AES-128-CFB1 128, AES-128-CFB8 128, AES-128-OFB 128, AES-128-GCM 128, AES-192-CFB 192, AES-192-CFB1 192, AES-192-CFB8 192, AES-192-OFB 192, AES-192-CBC 192, AES-192-GCM 192, AES-256-GCM 256, AES-256-CFB 256, AES-256-CFB1 256, AES-256-CFB8 256, AES-256-OFB 256, AES-256-CBC 256

IPsecXFRM, IKEv1, IKEv2, with 14 encryption methods for IPsec (3DES, DES, AES128, AES192, AES256, AES128GCM8, AES192GCM8, AES256GCM8, AES128GCM12, AES192GCM12, AES256GCM12, AES128GCM16, AES192GCM16, AES256GCM16)

GREGRE tunnel, GRE tunnel over IPsec support

PPTP, L2TPClient/Server instances can run simultaneously, L2TPv3, L2TP over IPsec support

StunnelProxy designed to add TLS encryption functionality to existing clients and servers without any changes in the program’s code

DMVPNMethod of building scalable IPsec VPNs, Phase 2 and Phase 3 and Dual Hub support

SSTPSSTP client instance support

ZeroTierZeroTier VPN client support

WireGuardWireGuard VPN client and server support

TincTinc offers encryption, authentication and compression in it's tunnels. Client and server support.

EoIPEthernet over IP (EoIP) tunnelling is a protocol based on GRE RFC 1701 that creates an Ethernet tunnel between two routers on top of an IP connection

OpenConnectCross-platform multi-protocol SSL VPN client which supports a number of VPN protocols

BacNET

Supported modesRouter

Supported connection typesIP

Configuration optionsSupport for multiple BACnet/IP interfaces, Network number assignment, Preconfigured BDT entries for BBMD (BACnet Broadcast Management Device)

OPC UA

Supported modesClient, Server

Supported connection typesTCP

MODBUS

Supported modesServer, Client

Supported connection typesRTU(RS232)

Custom registersMODBUS TCP custom register block requests, which read/write to a file inside the router, and can be used to extend MODBUS TCP Client functionality

Supported data formats8-bit: INT, UINT; 16-bit: INT, UINT (MSB or LSB first); 32-bit: float, INT, UINT (ABCD (big-endian), DCBA (little-endian), CDAB, BADC), HEX, ASCII

Data to Server

ProtocolHTTP(S), MQTT, Azure MQTT

Data to serverExtract parameters from multiple sources and different protocols, and send them all to a single server; Custom LUA scripting, allowing scripts to utilize the router's Data to server feature

MQTT Gateway

Modbus MQTT GatewayAllows sending commands and receiving data from MODBUS Server through MQTT broker

DNP3

Supported modesTCP Master, DNP3 Outstation

Supported connection typesRTU(RS232)

DLMS/COSEM

DLMS SupportDLMS - standard protocol for utility meter data exchange

Supported modesClient

Supported connection typesTCP, RTU(RS232)

CAN

CAN GatewayAllows forwarding CAN frames over IP networks.

API

Teltonika Networks Web API (beta) supportExpand your device's possibilities by using a set of configurable API endpoints to retrieve or change data.

Site Manager

Supported modesManager

FunctionalitiesCentralized management of TAP access points and Teltonika's managed switches — including device pairing and grouping, FOTA updates, device status monitoring, automatic reboot scheduling with ping/wget health checks, wireless SSID configuration, and VLAN assignment across the site.

Monitoring & Management

WEB UIHTTP/HTTPS, status, configuration, FW update, CLI, troubleshoot, multiple event log servers, firmware update availability notifications, event log, system log, kernel log, Internet status

FOTAFirmware update from server, automatic notification

SSHSSH (v1, v2)

SMSSMS status, SMS configuration

CallReboot, Status, Mobile data on/off, Output on/off, answer/hang-up with a timer, Wi-Fi on/off

TR-069OpenACS, EasyCwmp, ACSLite, tGem, LibreACS, GenieACS, FreeACS, LibCWMP, Friendly tech, AVSystem

MQTTMQTT Broker, MQTT publisher

SNMPSNMP (v1, v2, v3), SNMP Trap, Brute force protection

JSON-RPCManagement API over HTTP/HTTPS

RMSTeltonika Remote Management System (RMS)

IoT Platforms

ThingWorxAllows monitoring of: WAN Type, WAN IP, Mobile Operator Name, Mobile Signal Strength, Mobile Network Type

Cumulocity - Cloud of ThingsAllows monitoring of: Device Model, Revision and Serial Number, WAN Type and IP, Mobile Cell ID, ICCID, IMEI, Connection Type, Operator, Signal Strength. Has reboot and firmware upgrade actions

Azure IoT HubCan be configured with Data to Server to send all the available parameters to the cloud. Has Direct method support which allows to execute RutOS API calls on the IoT Hub. Also has Plug and Play integration with Device Provisioning Service that allows zero-touch device provisioning to IoT Hubs

AWS IoT CoreUtility to interact with the AWS cloud platform. Jobs Support: Call the device's API using AWS Jobs functionality

System Characteristics

CPUMediatek, 580 MHz, MIPS 24KEc

RAM128 MB, DDR2

FLASH storage32 MB, NOR Flash

Firmware/Configuration

WEB UIUpdate FW from file, check FW on server, configuration profiles, configuration backup

FOTAUpdate FW

RMSUpdate FW/configuration for multiple devices at once

Keep settingsUpdate FW without losing current configuration

Factory settings resetA full factory reset restores all system settings, including the IP address, PIN, and user data to the default manufacturer's configuration

FIRMWARE CUSTOMISATION

Operating systemRutOS (OpenWrt based Linux OS)

Supported languagesBusybox shell, Lua, C, C++

Development toolsSDK package with build environment provided

GPL customizationYou can create your own custom, branded firmware and web page application by changing colours, logos, and other elements in our firmware to fit your or your clients’ needs

Package ManagerThe Package Manager is a service used to install additional software on the device

Location Tracking

GNSSGPS, GLONASS, BeiDou, Galileo and QZSS

CoordinatesGNSS coordinates via WebUI, SMS, TAVL, RMS

NMEANMEA 0183

NTRIPNTRIP protocol (Networked Transport of RTCM via Internet Protocol)

Server softwareSupported server software TAVL, RMS

GeofencingConfigurable multiple geofence zones

Serial

RS232RS232 only TX and RX signals

CANIntegrated CAN interface

Serial functionsConsole, Serial over IP, Modem, MODBUS gateway, NTRIP Client

Input/Output

EventsEmail, RMS, SMS

SD CARD

Physical sizeMicro SD (internal)

ApplicationsSamba share

CapacityUp to 2 TB

Storage formatsFAT32, NTFS, ext2, ext3, ext4

POE IN

PoE ports1 x PoE In

PoE standardsActive PoE input 802.3af Class 0 (12.94 W) on LAN port

Power

Connector2-pin industrial DC power socket

Input voltage range9 - 57 VDC, reverse polarity protection 100 V max, surge protection min 64.4 V/max 71.2 V breakdown voltage, 93.6 V max reverse voltage @ 4.3 A max reverse surge current

PoE (passive)Passive PoE over spare pairs 4,5 (+) / 7,8 (-). Possibility to power up through LAN port, passive PoE voltage: 16 - 57 VDC

Power consumptionIdle: < 2 W, Max: < 3.5 W

Physical Interfaces

Ethernet2 x RJ45 ports, 10/100 Mbps

Status LEDs1 x Connection type status RGB LED, 1 x Connection strength RGB LED, 2 x ETH status LEDs, 1 x Power LED

SIM2 x internal SIM slots (Mini SIM – 2FF), 1.8 V/3 V, double stacked SIM tray

Power1 x 2-pin power connector

Antennas2 x SMA for Mobile, 1 x RP-SMA for Wi-Fi, 1 x SMA for GNSS

RS232, CAN1 x 6-pin terminal block

ResetReboot/User default reset/Factory reset button

Physical Specification

Casing materialAnodised aluminium housing and panels

Dimensions (W x H x D)83 x 25 x 83 mm

Weight140 g

Mounting optionsDIN rail, wall mount, flat surface (all require additional kit)

Operating Environment

Operating temperature-40 °C to 75 °C

Operating humidity10% to 90% non-condensing

Ingress Protection RatingIP30

Спецификации

Ethernet портове 2 Eth ports
PoE Да
Wi-Fi Wi-Fi 4
Клетъчна свързаност Клетъчни
Продуктова Гама Серия RUT2
Тип Рутери
208.68 € 222.00 €
Цена без ДДС: 173.90 € цена за брой
Спестявате: 13.32 € -6%

Отзиви0

0/ 5
средно за продукта
0
0
0
0
0
Този продукт няма отзиви.

Вие разгледахте